Whirlpool Range LP Conversion Kit WB28X47008 GGF4 GGF5

Range LP Conversion Kit – Whirlpool

Whirlpool Range LP Conversion Kit WB28X47008 GGF4 GGF5 This range lp conversion kit supports safe gas flow, burner ignition, flame distribution, grate stability, or fuel-type configuration. It is intended as a model-specific replacement for the service part listed below. Confirm the complete appliance model and serial number before ordering. Part-Specific Details LP Conversion Lit for models: GGF400PV1BB, GGF400PV1SS, GGF400PV1WW, GGF500PV1BB, GGF500PV1ES, GGF500PV1SS, GGF500PV1WW, GGF500PV2BB, GGF500PV2ES, GGF500PV2SS, GGF500PV2WW, GGF600AV1BB, GGF600AV1ES, GGF600AV1FS, GGF600AV1SS, GGF600AV1WW, GGF600AV2BB, GGF600AV2ES, GGF600AV2SS, GGF600AV2WW, GGS500PV1SS, GGS500PV2SS, GGS500SV1SS, GGS500SV2SS, GGS600AV1DS, GGS600AV1ES, GGS600AV1FS, GGS600AV1WW, GGS600AV2DS, GGS600AV2ES, GGS600AV2FS, GGS600AV2WW, GGS60LAV1FS, GGS60LAV2FS, XGF500PV1BB, XGF500PV1SS, XGF500PV1WW, XGF500PV2BB. Installation Instructions for (General Overview): (Note: These steps can vary, so always follow the manual specific to your appliance model). Turn Off Power and Gas : Before starting the installation, disconnect power to the appliance (unplug it or switch off the breaker) and turn off the gas supply to avoid any electrical or gas-related accidents. Remove the Old Part : For burner replacement, lift or remove the burner cap or cover (if applicable). For a switch or control board, remove the screws or clips securing the part in place. Disconnect any wiring connectors carefully. Prepare the New Part : Take the new part out of its packaging and inspect it for any visible damage. Align the part with the existing connection points (wiring, mounting holes, etc.). Install the New Part : If it's a burner, insert it into its mounting brackets and make sure it is secure. For switches or control boards, connect any wiring connectors and ensure they are fully plugged in. If Product Specifications Brand: Whirlpool Primary SKU: WB28X47008 Product type: Range LP Conversion Kit Application: model-specific range repair Verify burner position, cap diameter, finish, fuel type, orifice or coil specification, connector style, and kit contents Inspect burner ports, gas fittings, grounding, igniter alignment, and flame pattern Replaces / Cross-Reference Part Numbers WB28X47008, GGF4, GGF5, GGF6, GGS5, GGS6, XGF5 Cross-reference numbers can identify earlier revisions, distributor references, or approved service replacements. Compatibility can vary by production date and model revision. Symptoms of Failure Burner will not ignite or lights slowly uneven, yellow, lifting, or noisy flame repeated clicking gas valve will not open reliably cap rocks, grate is unstable, or fuel conversion is incorrect Installation Instructions Disconnect electrical power and shut off the gas supply. Allow all surfaces to cool, document burner and wiring locations, transfer only the parts specified for the model and fuel type, seat burner caps flat and centered, secure igniters without stressing ceramic, leak-test every disturbed gas fitting with an approved solution, restore power, and verify ignition and flame quality at each burner. Compatibility and Safety Confirm fit using the appliance rating label and Whirlpool-family parts diagram. Disconnect power and shut off water or gas when applicable, wear suitable protective equipment, preserve all shields and guards, and use a qualified technician for gas-system or unfamiliar electrical repairs.

Compatible Part Numbers

• WB28X47008
• GGF4
• GGF5
• GGF6
• GGS5
• GGS6
• XGF5

Key Features

• Product type: Range LP Conversion Kit
• SKU / MPN: WB28X47008

Fixes These Symptoms

• Burner will not ignite or lights slowly
• uneven
• yellow
• lifting
• or noisy flame
• repeated clicking
• gas valve will not open reliably
• cap rocks
• grate is unstable
• or fuel conversion is incorrect

Compatible Brands

• Whirlpool
• Maytag
• KitchenAid
• Amana
• Jenn-Air
• Roper
• Kenmore

Always verify your complete appliance model number before ordering.

Installation Guidance

Disconnect electrical power and shut off the gas supply. Allow all surfaces to cool, document burner and wiring locations, transfer only the parts specified for the model and fuel type, seat burner caps flat and centered, secure igniters without stressing ceramic, leak-test every disturbed gas fitting with an approved solution, restore power, and verify ignition and flame quality at each burner.